Page 1 of 1
Posted: Thu Dec 06, 2001 11:40 am
by PowerPuffGirl
Hello,
I'm planning on mounting the LK204-25PC inside the computer. What is the best way to connect the LCD to the serial port (DB9) outside the computer. TIA!
Posted: Thu Dec 06, 2001 12:27 pm
by linear
MO has a spiffy kit for that--you get a slot insert with a DB9 and a patch cord that's male-to-female DB9, so the only thing you see off the back panel is a short patch between two DB9 connectors. Very classy.
Don't know the part number or anything, but I'm sure Henry will be about shortly to clean up after me....
Posted: Thu Dec 06, 2001 1:03 pm
by PowerPuffGirl
I think I saw that on the accessories page. After looking closley it looked like the other end of the DB9 connector was an IDC. But perhaps the part you are referring to is probably available and I didn't see it. If that's the case, that would be perfect. Thanks Linear!
Posted: Thu Dec 06, 2001 1:11 pm
by relix
[off topic]
hey PuffthingyGirl, you've got a pic of yourself?
[/off topic]
jodynicH- I can feel the hormones
<font size=-1>[ This Message was edited by: jodynicH on 2001-12-06 15:43 ]</font>
Posted: Thu Dec 06, 2001 3:43 pm
by jodynicH
the -4BR connector is a molex header. It is only on by default on BLK/BVK202A-4BR displays. GLK12232-25 and GLK12232-25-SM can use it as well..
the -4BR connector is a molex header. It is only on by default on BLK/BVK202A-4BR displays. GLK12232-25 and GLK12232-25-SM can use it as well. I recommend taking a dremel and griding down a little slit on a slot cover for the back and making a small line of a slit on the top and run the cable throught that
<font size=-1>[ This Message was edited by: jodynicH on 2001-12-06 15:55 ]</font>
Posted: Thu Dec 06, 2001 4:42 pm
by PowerPuffGirl
*finger snap* Nope...sorry...Relix, I don't own a digital camera;)
Posted: Thu Dec 06, 2001 9:06 pm
by CyPher
i find the flat cable from mo is great for a clean install....ive got it mounted in my lian-li with double sided tape....dont use to much, just a piece every 6 inches or so...i run it outside the case through the bottom most pci slot cover, and mount it flat against the back.....looks neat as far as im concerned.....(though i think im going to change it to go up and along the top of the case, exiting under the power suppily....
Posted: Thu Dec 06, 2001 11:32 pm
by Henry
PowerPuffGirl, how is your soldering?
Posted: Fri Dec 07, 2001 6:46 am
by linear
One each of the first and last items on the
accessories page is what I had in mind (but was too lazy to provide linkage earlier).
Posted: Fri Dec 07, 2001 9:04 am
by PowerPuffGirl
My soldering skills are pretty sloppy;) What I might do is just cut a rounded small exit out of the back plate and snake the rounded serial connector out. Thanks to all who replied BTW.
Posted: Fri Dec 07, 2001 10:26 am
by relix
u'r welcome
just kidding
well, you're welcome, but I'm not the one who has to say that, now am I?
Posted: Fri Dec 07, 2001 4:08 pm
by jodynicH
Sorry Henry, you only like the women with good soldering skills....
Posted: Fri Dec 07, 2001 4:44 pm
by Henry
LOL.. yup
I did have a good solution if soldering wasn't a issue...
Posted: Wed Dec 12, 2001 8:51 am
by Psychodaemon
hopefully you have a motherboard with a
com 2 internal connector, use the internal-> external connector direct on the lcd..
no ugly cable going back into case from outside....
Posted: Mon Jan 07, 2002 3:13 pm
by Belaguez
Buy a motherboard like mine
ASUS CUSL2 C
Has a headed on the board that connects to a second serial port. Just take the serial connector off the slotin card they give you for it and you don't even have to have any cables outside your PC mines all internal.
Class